Datasheet: DS3/E3 inline probe ASE Model 807-0205 SKU 02210 Part Number 3621272 | NETSCOUT

Datasheet: DS3/E3 inline probe ASE Model 807-0205 SKU 02210 Part Number 3621272

With LinkSafe capabilities
Key Features:
  • Supports TruView™ and Visual Performance Manager™
  • Supports IP Transport and OmniPoint software
  • Capable of Inline placement with MSP certified fail to wire
  • Last mile keep alive upon CPE Router failure provides 100% availability and fault isolation
  • Configurable to support IPV4 or IPV6 management and monitoring
  • Inband and LAN management capable
  • Pro-active real time SNMP events with event forwarding
  • Continuous 1 second monitoring with burst analysis
  • Layer1 through 7 auto-detection and analysis
  • Server and application response time baselines and alarms
  • 1000 Concurrent VoIP calls with MoS scores
  • 4096 site to site SLA metrics per CoS
  • Rogue application discovery
  • On demand remote packet capture when required
 

 

Overview
The TruView and Visual Performance Manager DS3/E3* LinkSafe™ inline probe ASE complies with Class A standards for countries using DS3 access lines and supports digital transmission at the DS3 rate of 45 Mbps. This ASE supports IP Transport firmware for deployment in ATM-based data networks that use IP switching over DS3 physical lines.

The DS3/E3 ASE includes LinkSafe technology to protect circuit integrity in case of an ASE outage, as well as power failure notification.

This ASE is designed for deployment at the network demarcation point between a subscriber's CPE and the WAN. The figure below shows the ASE positioned between a Line Services Unit and a customer edge router on a DS3 line.

 

DS3/E3 ASE model
 
Inline probe ASE specifcations Model 807-0205 SKU 02210 Part Number 3621272
General Dimensions 1 EIA unit 1.69 x 17.09 x 24.69 (in) rack-mountable chassis
Weight 7 lbs.
Data Rate up to 45 Mbps synchronous
Timing Mode Derived externally from the network.
Environment Operating Temperature 0º to +40ºC (+32º to +104 º F)
Storage Temperature -20º to +55ºC (-4º to +131º×F)
Clearance Requirement Minimum of 3" (7.62 cm) space on sides.
Operating and Storage Humidity 10% to 90%, noncondensing
Power Requirements Input 100 to 240 VAC
Frequency 50/60 Hz
Input Current Rating 1.0 amps nominal
Network/User Interface Line Rate 44.736 Mbps
Line Coding B3ZS
Cell Scrambling On or Off
Line Build Out Long = more than 225 feet. Short = 225 feet or less.
Connector 4 BNC (75 ohm), Network Tx and Rx, CPE Tx and Rx
Impedance Input and Output 75 ohms
Pulse Shape Compliant ITU-T recommendation G.703
Framing C-bit or M23
Cell Delineation HEC or PLCP
Serial Port Interface Baud Rate 57600, 19200, or 9600 bps
Parity 8 data bits, no parity
Stop Bit 1 stop bit
Electrical Format EIA RS-232, DTE
Connector RJ-45
Serial Port Interface Baud Rate Selectable up to 19200 bps
Parity 8 data bits, no parity
Stop Bit 1 stop bit
Electrical Format EIA RS-232, DTE
Connector RJ-45
Ethernet 10/100BaseT Interface Bit Rate 10, 100, or 1000 Mbps
Connector RJ-45

 

What are ASEs?
ASEs (Analysis Service Elements) are data collection and network performance monitoring hardware devices placed on a wide area network (WAN) or Local Area Network (LAN) as part of the TruView and Visual Performance Manager systems. ASEs offer in-depth, real-time, and historical visibility into the performance of an applications infrastructure. Data gathered by ASEs is stored in the VPM server and displayed and analyzed from the Web portal interface. As a service level management tool, ASEs indicate when services are being met, provide warnings when services start to degrade, and send alerts when services are not met.

 

 

What is TruView and Visual Performance Manager
TruView and Visual Performance Manager are flexible solutions that can scale to help the largest enterprises, carriers and managed service providers decrease the cost of performance management, increase revenue, and optimize utilization of existing assets. This is accomplished by enabling IT organizations to become a source of competitive advantage, not a cost center, by providing actionable visibility into a centralized integration point for managing applications, VoIP network and server performance across a complete network.

 

 

Hardware Support
Enhanced ASE hardware warranty service programs are available to help you maximize your investment in TruView and Visual Performance Manager. For more detailed warranty information, visit www.netscout.com.

 

 

Software Maintenanced
Each hardware ASE is managed remotely by the TruView or Visual Performance Manager. Maintenance is dependent on the software module purchased. For more detailed maintenance information, visit Inside Sales at the number below.

 

 

Professional Services
Professional services are available for installing, maintaining and customizing your solution your ASE hardware and TruView and Visual Performance Manager solution. Replacing the hardware on site with or without a technician is offered worldwide. For more detailed professional services information, visit www.netscout.com/professionalservices.

 

 

Ordering Information
For more details, please visit www.netscout.com.